Stems

When stiffness and weight are the top on your list, you want Ritchey's SuperLogic C-260 Carbon Stem. This revolutionary design starts with a bar clamp that wraps a full 260-degrees around the handlebar to distribute clamping stress evenly through the handlebar, faceplate, hardware and stem body. Ritchey's first full-carbon stem, the C-260 features high-modulus carbon for stellar strength-to-weight ratio that translates into a solid but forgiving ride. And, the steer tube clamp uses three bolts and a curved slot to reduce clamp stress on the steer tube, so you can run carbon bars and a carbon steerer with no problem.

You really can have it all; Ritchey's WCS C-220 stem features revolutionary stiffness and classically inspired good looks, but it’s quick and easy to install and remove thanks to a press-fit handlebar clamp interface and forward-facing hardware. The C-220 handlebar clamp design creates a more secure interface by wrapping a full 220 degrees over the handlebar. Bolt forces are aligned with the clamp so that the stem body ‘embraces’ the handlebar, which is less prone to damaging lightweight bars. This clamp design allows for a lighter faceplate and stem body with no sacrifice in strength or stiffness. The stem body is forged 2014 aluminum for further weight reduction. Premium quality chromoly steel bolts are used throughout. - Material: 3d forged 2014 alloy body - 4 x 4mm coated CrMo steel forward-facing faceplate bolts - 2 x 4mm coated CrMo steel offset steer tube clamp bolts - 5Nm torque max on all hardware - Compatible with all 31.8 bars - Press-fit clamp design installs and removes like a standard stem - Angle: 84/6 degree - Steerer Height: 42mm - Steerer diameter: 1-1/8" - Faceplate Width: 42mm - Silver Finish - 121g (110mm)

The WCS C220 stem is easy to install and remove thanks to a press-fit handlebar clamp interface and forward-facing hardware. - The handlebar clamp design creates a more secure interface by wrapping a full 220 degrees over the handlebar - Bolt forces are aligned with the clamp so that the stem body embraces the handlebar which is less prone to damaging lightweight bars - Clamp design allows for a lighter faceplate and stem body with no sacrifice in strength or stiffness

You really can have it all—the new WCS C220 stem rivals the performance of the revolutionary C260 stem design, but it's quicker and easier to install and remove, thanks to a press-fit handlebar clamp interface and forward-facing hardware. First proven on the Ritchey TRAIL stem, the C220 handlebar clamp design creates a more secure interface by wrapping a full 220-degrees over the handlebar. Bolt forces are aligned with the clamp so that the stem body 'embraces' the handlebar, which is less prone to damaging lightweight bars. This clamp design allows for a lighter faceplate and stem body with no sacrifice in strength or stiffness. The Carbon Matrix stem body is forged 7075 aluminum with a stiffness-enhancing carbon exoskeleton which makes this 12% stiffer than the WCS alloy C220 stem. Premium quality CRMO steel bolts are used throughout. - Material: 3D forged 7075, carbon encased body - 4 x 4mm coated CrMo steel forward-facing faceplate bolts - 2 x 4mm coated CrMo steel offset steer tube clamp bolts - 5Nm torque max on all hardware - Compatible with all 31.8 bars - Press-fit clamp design installs and removes like a standard stem - Angle: 84/6 degree - Steerer Height: 42mm - Steerer: 1-1/8” - Faceplate Width: 42mm - Matte UD carbon finish - 126g (110mm)

A new breed of champion is born. The WCS Carbon Solostreem features a classic bend, UCI-compliant aero top section with short/shallow classic drop, integrated mount ready for K-Edge or similar devices, and underside grooved cable routing for a sleek appearance. It enjoys a matte UD carbon finish and its curved stem clamp greatly reduces steerer stress. - Material: Carbon monocoque with forged alloy steerer clamp - Stem Angle: 84 -degree - Drop/Reach: 126/75mm(Measured center-to-center where the levers mount) - Sweep/Flare: 4.7/1-degree - Features mounting holes for computer/accessory mount - Matte UD carbon finish - Weight: 350g (42cm x 100mm)

You really can have it all-the WCS C220 stem rivals the performance of the revolutionary C260 stem design, but it's quicker and easier to install and remove thanks to a press-fit handlebar clamp interface and forward-facing hardware. The WCS C22 25D Stem offers 25-degrees of positive or negative rise. First proven on the Ritchey Trail Stem, the C220 handlebar clamp design creates a more secure interface by wrapping a full 220 degrees over the handlebar. Bolt forces are aligned with the clamp so that the stem body 'embraces' the handlebar, which is less prone to damaging lightweight bars. This clamp design allows for a lighter faceplate and stem body with no sacrifice in strength or stiffness. The stem body is forged 2014 aluminum for further weight reduction. Premium quality CrMo steel bolts are used throughout. - Material: 3D forged and internally machined 2014 alloy body - CrMo faceplate bolts and patented 220 degree bar clamp design reduces weight, increases stiffness and distributes stress more evenly - Stainless steel steer tube bolts and curved clamp slot reduces weight and steer tube stress - 5Nm torque max on all hardware - Fits most road and mountain bars - Installs without the removal of levers - Angle: 25-degree - Stack: 45mm - Steerer: 1-1/8" - Faceplate Width: 40mm - Blatte finish - 120g (90mm)

- Bar Clamp Diameter: 31.8mm - Material: Alloy - Stem Angle: +17 degrees, -17 degrees - S.H.I.S. Stem Clamp Diameter: 31.8mm

Designed specifically for 1-1/8" steerer.

The RaceFace Aeffect 35 stem brings the advantages of a 35mm bar to the XC/Trail crowd at a mid-level pricepoint while maintaining a refined Race Face look. - Forged and machined from 6061 aluminum - Interlocking 4 bolt bar clamp secures your bar and distributes loads away from bolts - Stack Height: 39mm - Weight: 155g (60mm)

Origin-8's X-Tra Lift Stem Riser is an adapter that lets you raise your handlebars and stem. It fits over and securely bolts to 1 1/8-inch forks to extend them. This gives you more height to raise your stem/bars. You use the included spacers to dial in the best fit. The Stem Riser is made from forged 6061 aluminum and is anodized for durability.

Enduro has unquestionably evolved ever closer to Downhill. The Enduro MK3 Stem is all you need for hitting the trails with wingsuit type accuracy. This Stem was born out of rider's demands for precision and for those moments when you have to be inch-perfect. Taking design elements from our World Cup-winning Direct Mount MK3 Stem and splicing these with our critically acclaimed Enduro MK2 Stem. We developed the Stem specifically with Pro's and Bro's alike. It was obvious we all live for the same challenge of pushing our own limits. As riders, we want a Stem that inspires confidence to change lines through the middle of a rock garden like it's no big deal or slap the inside of a turn and translate all your weight to front-wheel traction. Providing ear-to-ear grins and saying to your mates at the bottom of a trail, "Did you see that?". From the start of the design process, it became clear that we wanted extra rigidity. To yield this, we would need to make the Stem using a forging process - a new thing for us. The result of this allowed us to achieve a more intricate shape than machining alone. It involves applying a huge amount of force to redirect the grain flow of the material. As a result, this gives superior strength, fatigue and impact resistance. Another area where we made a significant improvement in rigidity was by increasing the clamping surface area on the steerer tube. We've vastly increased this to give a stout, rock-solid feel and as close to the MK3 Direct Mount Stem as we could. Furthermore, everything is held securely by stainless steel bolts to ensure there is no rust even in the grimmest weather. In addition and like every Burgtec product, it's fully CNC machined and anodized in all your favourite flavours. Tested with the world's fastest jibbers and sendiest racers, this stem has everything you need to hit all those rowdy racing lines or pull that little bit harder off that big sender. - Forged and Fully CNC machined from AL6061 – T6 Aluminium - Stainless Steel Hardware - Available lengths - 35mm, 42.5mm and 50mm - Available in both 31.8mm (Black only) and 35mm Clamp - Weight: 35mm 138g, 42.5mm 152g, 50mm 160g

Save your steerer tube and eliminate headset spacers with the Velo Orange Tall-Stack alloy stem. It gives your bike's cockpit a nice clean look. Available in Polished or Black, the 17-degree angle allows the stem to be level on most modern frames. And, you can use handlebar clamp shims to adapt to smaller handlebar clamp diameters, if you like. - Stack height: 75mm - Not recommended for use with carbon steerer tubes

The BrickTop alloy stem is a classic style, top-mount BMX stem with a 4-bolt handlebar clamp.

With its alloy/steel construction and 4-bolt clamp design, the MX is a trusty BMX quill stem. - Quill Length: 4-1/4-inches - Quill diameter: 21.1mm

The DefendR BMX threadless stem has a AL6061 forged alloy construction and a 4-bolt face clamp. - 30mm stack height - 240g

An aerodynamically honed stem with adjustable length and angle to optimize your position. The rider makes up 80-90% of total aero drag, so refining your position can produce some of the biggest gains of all. Further, the shape of the stem, plus the ability to eliminate headset spacers, allows for cleaner airflow at the front of the bike, producing valuable drag reduction. Created in conjunction with Team Dimension Data, the stem delivers the confident and responsive ride feel demanded by the best riders in the world. This stem is intended for negative drop only and cannot be flipped or reversed in a positive rise. - Material: Carbon - Faceplate Material: Aluminum - Hardware Material: Titanium - Stack Height: 42.5mm with length shim / 45.5mm with angle shim - Torque Spec, Face Plate Upper Bolt: 10Nm, Lower Bolt: 6Nm - Torque Spec, Steer Tube: 5.5Nm

Simple, elegant, lightweight design can be run in negative or positive position for -17°/ 17° in rise. 3D forged 6061-T6 aluminum combined with a 4-bolt faceplate provides increased stiffness. - Weight: 162g (100mm) - Length: 70, 80, 90, 100, 110, 120, 130mm (±17°) - Material: 3-D Forged 6061-T6 Aluminum - Clamp Diameter: 31.8mm - Angle: 73° (±17°) - Steerer Tube Diameter: 11/8in - Stack Height: 40mm - Clamp Width: 40mm - Clamp Tourque: 5Nm - Finish: Matte Black with White Accents

Tom Dugan's signature DGN v2 stem is a classic top-load, 6-bolt design. Along with other Odyssey v2 stems, the bolt heads have been upgraded to a larger size and the clamping area features unique surface contouring for superior handlebar grip - Six bolt clamping configuration - Headset pre-load bolt recess (32mm diameter)

- 3D forged 6061 alloy road stems in 6 or 17 degree angles - Lightweight 4 bolt faceplate - Material: AL6061-T6 - Finish: Sandblasted

FSA ACR (Aerodynamic Cable Routing) Stems have a low-profile frontal area that is suitable for road and gravel riding. - Aerodynamic Cable Routing (ACR) - Low-profile frontal area - No rotation limit - Body and faceplate - 6061 T6 - Chromoly hardware - Specific frame and headset required - 31.8mm handlebar clamp diameter - 30mm fork clamp stack height - Compatible with: K-Force Light ACR Compact, SL-K ACR Compact, Energy ACR Compact, K-Wing AGX and K-Wing AGX handlebars

Profile's Aris stem is a no-nonsense stem made from 6061-aluminum that's been shot-peened and anodized for strength and durability. The 4-bolt face plate is stiff, ultra tough and makes handlebar changes a breeze. And, the opposing-bolt steerer clamp is safe and secure.

Sunlite's Adjustable Quill Stem puts your bars right where you want them. This wonderfully easy-to-use stem adjusts from 0 to +50 degrees—more than enough to help you find your ideal position. And, the 2-bolt clamp holds securely holds your bars.

• Forged aluminum • Single-bolt clamp • 180mm tall

• Forged aluminum • 2-bolt clamp • 250mm tall (extra tall)

• Forged aluminum • 2-bolt clamp • 180mm tall

• Steel • Polished-chrome finish • 1-inch model has 22.2mm quill, 15/16-inch model has 21.1mm quill • 10-inches tall (extra tall)

Whisky's No.7 Mountain stems offer a stout connection for modern mountain bars. They match the simple, clean aesthetic of other Whisky cockpit components. - Bead-blasted, then anodized, finish - 3D-forged for increased strength, then CNC-machined - 4-bolt faceplate design for easy installation

The Chester 35 Direct Mount stem is a practical 2-piece design with big bold graphics and that legendary bomb-proof Race Face toughness baked right in. - The Chester 35 direct mount stem is an all new 2 piece direct mount design - Forged and machined from 6061 aluminum - Weight saving single bolt faceplate - Four bolt bar clamp holds bar securely in position. - Interlocking U-Shaped Handlebar Clamp Geometry transferring more load through the stem body and not the bolts - Faceplate eliminates 'stress risers' which can cause your bar to bend or break

- Forged AL6061-T6 alloy construction - Matte finish with laser-etched graphics - ISO-Mountain safety certified - 4-bolt handlebar clamp - Quill length: 180mm

All Box stems are engineered and crafted using our Oversized Technology. As we follow the load paths down the handlebars we have focused our attention on the stem-to-bar interface. Since the Oversized handlebars have an increased wall thickness and tube diameter in this sector we have reciprocated with an augmented stem interface with greater surface area. We’ve done this by moving material from low stress areas. This has greatly minimized twist and contributed to responsiveness. As the stem in mated with the handlebars we have contributed to increased pedaling stiffness by providing a backstop to the “lifting” phenomenon. There is no point pushing hard on your pedals if you can’t pull up on your handlebars and deliver that power. Power can easily be lost to handlebar-to-stem deflection and the consequences can be poor power delivery and steering control. When combined with Box’s other Oversized components, you’ll experience heightened responsiveness and reduced latency. Key differences: In this particular model stem we’ve modulated the Oversized formula to emphasize pedaling stiffness. We have transferred material specifically to sectors that experience sudden stress from pulling up on the handlebars. You’ll feel a difference in your acceleration. These stems are engineered for the larger-sized racers. -Material: 6061-T6 Aluminum -Process: Cold-Forged -Hardware: Chromoly Clamping Bolts -Finish: Anodized w/Laser-Etched Graphics Weight: -48mm: 280 g / 9.8 oz -53mm: 290 g / 10.2 oz